seymour duncan wiring diagrams jb junior for strat

SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT HOW TO
SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT INSTALL
SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT MOD
SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT PLUS

Next, solder the Black Wire to the first tab on the Volume control. Solder the Green Negative wire and the Bare wire to the back of the Volume pot, which is the standard place to solder all Ground wires (Fig 3).

SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT INSTALL

Now we are left with the positive (Black) and negative (Green) wires that we will need to install our pickup. Finally, following standard practice, and using Green as the Ground, we solder the Green and Bare wires together (Fig 2). We solder the Red and White wires together and tape them off. So, we begin our SH-4 JB installation by identifying the Black Wire as the Hot. Combining the two makes the humbucker almost twice as loud as a single-coil, and it is also responsible for its warmer tones because of phase cancellation. This means that we run one coil right into the other to create one long continuous path for our signal to travel. The “standard” way to wire humbuckers is in Series. Wiring Codeįor the Seymour Duncan SH-4 JB, one coil uses Green and Red while the other uses Black and White (Fig 1).

The Shield and the coils are not connected, but the Shield does connect to Ground. Its primary purpose is to trap radio frequencies that reach the pickup and shuttle them to Ground before they degrade your signal. The color that goes to each is called the pickup’s “Wiring Code.” Unfortunately, there is no standard Wiring Code, and it varies between manufacturers. Each coil has a positive and a negative wire. The four colored wires are called “conductor” wires because each of them carries current to and from the two coils in the humbucker. It’s a high-output, versatile pickup that sounds very good in the Neck and Bridge positions. The SH-4JB is a humbucker that uses a balanced coil configuration to produce improved harmonics with just the right blend of sustain and distortion. Activating the switch will bypass all controls and all pickups connected to the pickup selector switch are wired directly to the output jack.In the Seymour Duncan SH-4 JB wiring that we’ll be doing, the pickup is installed using four colored conductor wires and a bare wire.

SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT HOW TO

You can see how to wire the switch on the circuit below. Another way to do this is to use a DPDT switch or a push/pull pot and to perform my 'direct-through' mod.Electrically this pots are great when you open them 100%, a circuit will shorten this pot and erase it from the circuit, so it''s as if it never was there. This is a very cool, albeit an expensive, way to enhance the sound of your guitar. You can replace all your pots with so-called 'no-load' pots from Fender.However, there are different ways to get rid of the control load in your guitar system: As you may recognize, the suggested method works well, but is not practicable in any way. The control pots always add a little load to the circuit and, depending on the pots, the tone will get a bit softer and sometimes dull, losing the shimmering highs and the organic vibe.

SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT MOD

Depending on the guitar, the result can be stunning with a Tele, your tone will be louder, stronger and more direct, a highly recommended mod for all the country guys, as well as anyone who wants the maximum twang and spank a Tele has to offer. If you really want to hear the sound of your guitar together with the pickup, there is only one way: soldering the pickup directly to the output jack.

If one day you decide to switch back to the classic two-pickup Tele configuration, you can simply take out the middle pickup, switch back to a 3-way Telecaster switch and reinstall a standard Telecaster pickguard that will cover the third pickup cavity suddenly, the former modification is invisible again. Basically, this is a standard Strat configuration and naturally you can perform any Stratocaster mod you like (the 7-tone mod, blending options, etc.), but we will talk about all this Strat stuff in a later column. You will also have to change the 3-way switch and install a standard Stratocaster 5-way switch and eventually a third pot if needed. If you want to modify your Tele this way, I recommend giving it to an experienced luthier and letting him do the necessary woodwork (routing the additional pickup cavity, rerouting the pickguard, etc.).Īny Stratocaster pickup is a good mate for the standard Telecaster pickups and will expand your tonal palette drastically.

SEYMOUR DUNCAN WIRING DIAGRAMS JB JUNIOR FOR STRAT PLUS

Many of the top Nashville studio players, like Brent Mason or Reggie Young, are playing Telecasters with an additional third pickup in the middle position to get those popular 'in-between' Strat sounds (bridge plus middle and middle plus neck together in parallel). The 'Strato-tone' Mod (aka 'Nashville' Modification)

Seymour duncan wiring diagrams jb junior for strat